Ambient air is drawn in by the fan and passed over the evaporator. The evaporator cools the air, i.e. it extracts the heat it contains. In the evaporator, the heat removed is transferred to the working fluid (refrigerant). With the aid of an electrically driven compressor, the absorbed heat is “pumped” to a higher temperature level through an increase in pressure and given off to the heating water via the condenser (heat exchanger). In so doing, the electrical energy is used to raise the heat of the environment to a higher temperature level. Due to the fact that the heat energy extracted from the air is transferred to the heating water, this type of appliance is referred to as an air source heat pump. The air source heat pump consists of the following main components: Evaporator, fan and expansion valve as well as the low-noise compressor, the condenser and the electric control unit consisting of branded equipment for controlling and safety devices for protection of Compressor, pump etc. against any variations in voltage, current. Also consists of trip devices, if any parameters not available for smooth running of Heat Pump. The Heat Pump is connected to a Hot Water Storage Tank which is made of 4 mm M.S. Sheet, is insulated with rock wool, for maximum temperature sustenance.. Once the temperature in Tank reaches 55°C the machine automatically shuts down and again re-starts when the temperature reduces to 52°C. There is 24 x 7 uninterrupted Hot Water for the whole year, unconditional to any seasons or weather, unlike solar heaters which are completely dependent on Weather conditions.

A water softener should last 10 to 15 years. If your unit is facing more wear and tear, it could be due to improper maintenance or particularly hard water. If you'd like to extend the lifespan of your water softener, one option is to add a pre-filter.

Sand filtration is used for the removal of suspended matter, as well as floating and sinkable particles. The wastewater flows vertically through a fine bed of sand and/or gravel.

Carbon filters remove contaminants through adsorption. Adsorption means that contaminants are attracted to the surface of the activated carbon and held to it, much the same way a magnet attracts and holds iron filings. Carbon filters also act as a catalyst to change the chemical composition of some contaminants.

. DM Water systems produces high quality water free from any kind of minerals. It operates on the principle of ion exchange, degasification and polishing for treating water and removing ions. Demineralization technology is one of the cost effective solutions for treatment of water. These systems are widely used to treat water in the field of steam, power, process, and cooling.

Zero B offers advanced and uniquely designed water softeners for homes that convert hard water into soft water

In an RO system, pressure is utilized to overcome natural osmotic pressure, forcing the source water with its dissolved salts and other contaminants through a semipermeable membrane. This membrane removes a high percentage of the impurities, resulting in highly purified water

Ambient air is drawn in by the fan and passed over the evaporator. The evaporator cools the air, i.e. it extracts the heat it contains. In the evaporator, the heat removed is transferred to the working fluid (refrigerant). With the aid of an electrically driven compressor, the absorbed heat is “pumped” to a higher temperature level through an increase in pressure and given off to the heating water via the condenser (heat exchanger). In so doing, the electrical energy is used to raise the heat of the environment to a higher temperature level. Due to the fact that the heat energy extracted from the air is transferred to the heating water, this type of appliance is referred to as an air source heat pump. The air source heat pump consists of the following main components: Evaporator, fan and expansion valve as well as the low-noise compressor, the condenser and the electric control unit consisting of branded equipment for controlling and safety devices for protection of Compressor, pump etc. against any variations in voltage, current. Also consists of trip devices, if any parameters not available for smooth running of Heat Pump. The Heat Pump is connected to a Hot Water Storage Tank which is made of 4 mm M.S. Sheet, is insulated with rock wool, for maximum temperature sustenance.. Once the temperature in Tank reaches 55°C the machine automatically shuts down and again re-starts when the temperature reduces to 52°C. There is 24 x 7 uninterrupted Hot Water for the whole year, unconditional to any seasons or weather, unlike solar heaters which are completely dependent on Weather conditions.

Ambient air is drawn in by the fan and passed over the evaporator. The evaporator cools the air, i.e. it extracts the heat it contains. In the evaporator, the heat removed is transferred to the working fluid (refrigerant). With the aid of an electrically driven compressor, the absorbed heat is “pumped” to a higher temperature level through an increase in pressure and given off to the heating water via the condenser (heat exchanger). In so doing, the electrical energy is used to raise the heat of the environment to a higher temperature level. Due to the fact that the heat energy extracted from the air is transferred to the heating water, this type of appliance is referred to as an air source heat pump. The air source heat pump consists of the following main components: Evaporator, fan and expansion valve as well as the low-noise compressor, the condenser and the electric control unit consisting of branded equipment for controlling and safety devices for protection of Compressor, pump etc. against any variations in voltage, current. Also consists of trip devices, if any parameters not available for smooth running of Heat Pump. The Heat Pump is connected to a Hot Water Storage Tank which is made of 4 mm M.S. Sheet, is insulated with rock wool, for maximum temperature sustenance.. Once the temperature in Tank reaches 55°C the machine automatically shuts down and again re-starts when the temperature reduces to 52°C. There is 24 x 7 uninterrupted Hot Water for the whole year, unconditional to any seasons or weather, unlike solar heaters which are completely dependent on Weather conditions.

A reverse osmosis (RO) plant is a water treatment facility that uses reverse osmosis technology to purify water by removing contaminants, dissolved salts, and impurities. Below are different aspects and descriptions of an RO plant based on its components, applications, and operations: General Description Definition: A reverse osmosis plant is a water purification system that applies pressure to force water through a semi-permeable membrane, effectively removing impurities, salts, and microorganisms. Purpose: It is designed to provide high-quality water for drinking, industrial processes, irrigation, or specific uses like medical applications. Components Pretreatment System: Includes filters, water softeners, and dosing systems to remove large particles, chlorine, and other contaminants that could damage the RO membranes. High-Pressure Pump: Generates the necessary pressure to push water through the semi-permeable membranes, overcoming the natural osmotic pressure. RO Membranes: The core of the plant, designed to allow only water molecules to pass while blocking salts, minerals, and impurities. Post-Treatment System: May include UV sterilization, pH adjustment, or remineralization to make the purified water suitable for its intended use. Control System: Automates the operation, monitors parameters, and ensures the plant functions efficiently and safely. Applications Drinking Water Production: Supplies potable water in urban, rural, or disaster-relief settings. Industrial Use: Produces ultrapure water for pharmaceuticals, electronics manufacturing, and power plants. Desalination: Converts seawater into fresh water in arid regions or areas with limited freshwater resources. Irrigation: Provides purified water for agriculture, ensuring crop health by reducing salinity. Wastewater Treatment: Recycles wastewater by removing contaminants for reuse. Advantages Produces high-quality water with minimal impurities. Removes a wide range of contaminants, including heavy metals, dissolved salts, and bacteria. Energy-efficient compared to thermal desalination processes. Scalable, from small household units to large industrial plants. Limitations Requires a significant amount of feed water, as some is rejected as waste. Regular maintenance and replacement of membranes are necessary. Energy-intensive, especially for high-pressure systems. Pretreatment is critical to avoid fouling and scaling of membranes. Environmental Impact Positive: Provides clean drinking water, supports sustainable water management, and reduces dependency on groundwater. Negative: Brine disposal from the plant can harm the environment if not managed properly.

Ambient air is drawn in by the fan and passed over the evaporator. The evaporator cools the air, i.e. it extracts the heat it contains. In the evaporator, the heat removed is transferred to the working fluid (refrigerant). With the aid of an electrically driven compressor, the absorbed heat is “pumped” to a higher temperature level through an increase in pressure and given off to the heating water via the condenser (heat exchanger). In so doing, the electrical energy is used to raise the heat of the environment to a higher temperature level. Due to the fact that the heat energy extracted from the air is transferred to the heating water, this type of appliance is referred to as an air source heat pump. The air source heat pump consists of the following main components: Evaporator, fan and expansion valve as well as the low-noise compressor, the condenser and the electric control unit consisting of branded equipment for controlling and safety devices for protection of Compressor, pump etc. against any variations in voltage, current. Also consists of trip devices, if any parameters not available for smooth running of Heat Pump. The Heat Pump is connected to a Hot Water Storage Tank which is made of 4 mm M.S. Sheet, is insulated with rock wool, for maximum temperature sustenance.. Once the temperature in Tank reaches 55°C the machine automatically shuts down and again re-starts when the temperature reduces to 52°C. There is 24 x 7 uninterrupted Hot Water for the whole year, unconditional to any seasons or weather, unlike solar heaters which are completely dependent on Weather conditions.

In an RO system, pressure is utilized to overcome natural osmotic pressure, forcing the source water with its dissolved salts and other contaminants through a semipermeable membrane. This membrane removes a high percentage of the impurities, resulting in highly purified water